• Install Unisteer rack and pinion 1/2007

• Test fit engine/tranny 1/2007

• Review/fab/puchase TKO rear mount 1/2007

• Final build custom export brace 1/2007

• Mark headers for rack and pinion clearance - 1/2007

• Solder ignition switch connector back to harness - 1/2007

• Sort under dash to EFI harness connections

• Solder connector(s) for under dash to EFI harness

• Route EFI fuel pump(s) power trigger run to rear of car 1/20/2007

• Route EFI pump sensor wire to rear of car 1/20/2007

• Test fit C&L air intake and 80mm mass air 1/2007

• Build bracket to mount mass air 1/2007

• Extend mass air wiring outside of engine bay 1/2007

• Purchase Heater seal kit - 1/2007

• Purchase heater core (O'Reillys) - 1/2007

• Clean/paint lower dash - 1/2007

• Purchase proper size shrink wrap for main wiring

• Measure/source/select drive shaft for TKO 1/2007

• Mark O2 sensor locations on headers - 1/2007

• Mount/wire horn relay under hood by other relays 1/21/2007

• Purchase misc EFI pigtails http://rjminjectiontech.com/?p=10  1/20/2007

  • Ignition coil - $12

  • Oxygen sensor (3 wire) - $15 x 2

  • Vehicle speed sensor - $15

  • Inertia Cut off - $8

  • Fuel injector (for clean/test) - $6

  • EGR Eliminator - $20 - Easier than tracking it all down myself

  • Harness tape $2 / 100' roll

• Purchase Injector rebuild kit 1/20/2007

•  

• Purchase standard aluminum radiator

• Purchase qty 3 four circuit fuse blocks (inside, front, rear)
• Purchase 3/8" aluminum fuel line - May 2007
• Purchase front AN bulkhead and other fittings - May 2007
• Purchase O2 bungs for headers
• Fab mounting brackets for radiator
• Wire up harness to electric fan relay
• Locate/install INSIDE four circuit fuse box
  • 1) O2, 2) Computer, 3) Alarm/Entry, 4) Spare
• Locate/Install FRONT four circuit fuse box
  • 1) Fan, 2) Headlight, 3) Horn, 4) Spare
• Run power for Fans, Headlights, and horn from relay box
• Remove mocked engine/trans
• Finalize steering linkage function
• Fab TKO slave mounting bracket
• Install O2 bungs for headers
• Purchase O2 sensors
• Purchase O2 extension for cutting up for integration
• Purchase or build harness for backup lights and neutral start
• Wire backup and neutral into existing connector
• Finish clean up of rear under carriage
• Make clearance for rack and pinion on headers
• Finalize brake lines (need large end for rear on master cylinder)
• Finalize/test line lock install
• Final run front headlight, etc harness
• Run left side wiring to rear
  • Left/Right speakers, trunk release, amp power trigger, defogger trigger
• Purchase EFI fuel pump, low pressure pump, filter and surge tank - May 2007
• Build mounting bracket for pumps and surge tank
• Test power up without computer or other connections - low voltage??

• Purchase B-Quite Sound deadner

• Install B-Quite on firewall

• Install lower dash

• Clean/rebuild heater w/ new core and seals
• Cut hood bracing for intake tube and supports

• Install inside primary wiring harness

• Purchase mixed size U Joints for drive shaft

• Purchase wire and wire ends for electric fans

• Install canister status bypass resistors inside car

• Tap O2 sensor wires at computer for Air/Fuel Gauge

•  

• Purchase full floor pans - May 2007
• Weld in floor pans
• Seam seal floor pans
• Rust proof and paint floor pans
• Weld up and re-enforce rear shock support area
• Cut out / repair minor rust in front of rear wheel well
• Paint under hood and firewall
• Install REAR four circuit fuse box
  • 1) Fuel Pump(s), 2) Stereo Amp, 3) Trunk light/power, 4) Defogger (if used)
• Rust and panel repair rear panel and support
• Review/install electric trunk release option

• Test fit old exhaust for initial use

• Fab rear muffler hangers as needed

• Test fit inner rear 1/4 molding for wheel well mod clearance

• Install EGR bypass resistors inside car

• Clean/rebuild 24lb injectors ( http://fordfuelinjection.com/?p=82 )

•  

• Purchase drive shaft loop
• Install drive shaft loop
• Purchase 5.0 Roller Block - April 2007
• Purchase 347 Stroker kit - May 2007
• Purchase TFS Cam
• Purchase Roller Lifters

Back to the Stang Page | Back to Rebuild Page